Pregled nacrta

prEN 1501-2 - Refuse collection vehicles - General requirements and safety requirements - Part 2: Side loaded refuse collection vehicles
Odbor: HZN/TO 522 (Gospodarenje otpadom i karakterizacija mulja)
Ustanova izvornika:
Rok za komentiranje: 2025-07-28
Podaci o nacrtu
Prikaži višePrikaži manje
 
This document applies to side loaded refuse collection vehicle (RCV), as defined in 3.2, regardless of the power drive.
This document deals with all significant hazards, hazardous situations and events relevant to the side loaded RCV, when it is used as intended and under conditions of misuse which are reasonably foreseeable, throughout its foreseeable lifetime, as defined in Clause 4.
This document is applicable to the design and construction of the side loaded RCV so as to ensure that it is fit for its intended function and can be operated, cleaned (including unblocking), adjusted and maintained during its entire lifetime. It is not applicable to the end of life of the side loaded RCV.
This document describes and defines the safety requirements of side loaded RCV excluding the interface with the lifting device(s) and excluding the lifting device itself and excluding loader cranes, which could be mounted on the RCV.
Lifting device(s) including the loader cranes and the interface to the RCV are covered in EN 1501-5:202X.
Loader cranes are covered in EN 12999:2020+A1:2025 and those installed on RCVs are covered in EN 1501-5:202X.
This document also applies to compactors, operated on a truck for collecting purposes.
This document is not applicable to:
- operation in severe conditions, e.g. extreme environmental conditions such as:
- below −20 °C and above +40 °C temperatures;
- tropical environment;
- wind velocity in excess of 75 km/h;
- contaminating environment;
- corrosive environment;
- operation in potentially explosive atmospheres;
- handling of loads the nature of which could lead to dangerous situations (e.g. hot refuses, acids and bases, radioactive materials, contaminated refuse, especially fragile loads, explosives);
- operation on ships.
This document is not applicable to machinery which is manufactured before the date of publication of this document by CEN.
prEN 1501-3 - Refuse collection vehicles - General requirements and safety requirements - Part 3: Front loaded refuse collection vehicles
Odbor: HZN/TO 522 (Gospodarenje otpadom i karakterizacija mulja)
Ustanova izvornika:
Rok za komentiranje: 2025-07-28
Podaci o nacrtu
Prikaži višePrikaži manje
 
This document applies to a front loaded refuse collection vehicle (RCV), as defined in 3.2, regardless of the power drive.
This document deals with all significant hazards, hazardous situations and events relevant to the front loaded RCV, when it is used as intended and under conditions of misuse which are reasonably foreseeable, throughout its foreseeable lifetime, as defined in Clause 4.
This document is applicable to the design and construction of the front loaded RCV so as to ensure that it is fitted for its intended function and can be operated, cleaned (including unblocking), adjusted and maintained during its entire lifetime. It is not applicable to the end of life of the front loaded RCV.
This document describes and defines the safety requirements of the front loaded RCV excluding the interface with the lifting device(s) and excluding the lifting device itself and excluding loader cranes, which could be mounted on the RCV.
Lifting device(s), loader cranes and their interface to the RCV are covered in EN 1501-5:202X.
Loader cranes are covered in EN 12999:2020+A1:2025 and those installed on RCVs are covered in EN 1501-5:202X.
This document also applies to compactors, operated on a truck for collecting purposes.
This document is not applicable to:
- operation in severe conditions, e.g. extreme environmental conditions such as:
- below −20 °C and above +40 °C temperatures;
- tropical environment;
- wind velocity in excess of 75 km/h;
- contaminating environment;
- corrosive environment;
- operation in potentially explosive atmospheres;
- handling of loads the nature of which could lead to dangerous situations (e.g. hot refuses, acids and bases, radioactive materials, contaminated refuse, especially fragile loads, explosives);
- operation on ships.
This document is not applicable to machinery which is manufactured before the date of publication of this document by CEN.
prEN 1501-5 - Refuse collection vehicles - General requirements and safety requirements - Part 5: Lifting devices for refuse collection vehicles
Odbor: HZN/TO 522 (Gospodarenje otpadom i karakterizacija mulja)
Ustanova izvornika:
Rok za komentiranje: 2025-07-28
Podaci o nacrtu
Prikaži višePrikaži manje
 
This document deals with all significant hazards, hazardous situations and events relevant to lifting devices used for the emptying of designated refuse containers into RCVs and their fitting onto the RCVs when they are used as intended and under conditions of misuse which are reasonably foreseeable throughout their foreseeable lifetime as defined in Clause 4.
This document is applicable to the design and construction of the refuse container lifting devices and the mounting of other lifting devices so as to ensure that they are fitted for their function and can be operated, adjusted and maintained during their entire lifetime. It is not applicable to the end of life of the lifting devices.
This document describes and gives the safety requirements of the lifting devices for emptying refuse containers and their interfaces with the corresponding parts of the RCVs and will be used in conjunction with EN 1501-1:202X for the rear, side and front loaded RCVs. It refers to EN 1501-4:2023 for the noise test code.
This document is not applicable to:
- operation in severe conditions e.g. extreme environmental conditions such as:
- temperatures below −20 °C and above +40 °C;
- tropical environment;
- wind velocity in excess of 75 km/h;
- contaminating environment;
- corrosive environment;
- operation in potentially explosive atmospheres;
- lifting and transportation of persons;
- emptying refuse containers other than those manufactured according to EN 840:2020 series, EN 12574:2017 series, EN 13071:2019 series, and those described as paladin, diamond, skip containers;
- loading bulky refuse by means of platform or forks;
- handling of loads the nature of which could lead to dangerous situations (e.g. hot refuses, acids and bases, radioactive materials, contaminated refuse, especially fragile loads, explosives);
- operation on ships;
- fitting and operation on stationary compactors.
This document is not applicable to machinery which is manufactured before the date of its publication by CEN.
EN 1594:2024/prA1 - Gas infrastructure - Pipelines for maximum operating pressure over 16 bar - Functional requirements
Odbor: HZN/TO 505 (Prijenos i distribucija plina)
Ustanova izvornika:
Rok za komentiranje: 2025-07-28
Podaci o nacrtu
Prikaži višePrikaži manje
 
This document describes the functional requirements for pipelines for maximum operating pressure over 16 bar. This document also describes the mechanical requirements for pipework in stations with a maximum operating pressure greater than 16 bar.
NOTE 1 Welding requirements are described in EN 12732. Functional requirements for stations are given in EN 1776, EN 1918-5, EN 12186, and EN 12583.
This document is applicable for transporting gas via onshore high-pressure steel pipeline infrastructures, where the following applies:
- onshore:
- from the point where the pipeline first crosses what is normally accepted as battery limit between onshore and offshore, and that is not located within commercial or industrial premises as an integral part of the industrial process on these premises except for any pipelines and facilities supplying such premises;
- pipeline system with a starting point onshore, also when parts of the pipeline system on the mainland subsequently cross fjords, lakes, etc.
- high pressure: gas with a maximum operating pressure over 16 bar and a design temperature between −40 °C and 120 °C.
- steel pipeline infrastructure: infrastructure consisting of pipeline components, such as pipes, valves, couplings and other equipment, restricted to components made of unalloyed or low alloyed carbon steel and joined by welds, flanges or mechanical couplings.
- gas: non-corrosive natural gas, biomethane gas, hydrogen gas and mixtures of these gases where technical evaluation has ensured that operating conditions or constituents or properties of the gas do not affect the safe operation of the pipeline.
Gas infrastructures covered by this document begin after the gas producer's metering station.
NOTE 2 The functional demarcation of the pipeline system is usually directly after an isolating valve of the installation, but can differ in particular situations. The functional demarcation of the pipeline system is usually located on an isolating valve of the installation, but can differ in particular situations.
A schematic representation of pipelines for gas infrastructure is given in Figure 1.
This document can also be applied to the repurposing of existing pipelines.
 
[Figure 1 - Schematic representation of pipelines for gas supply over 16 bar]
 
This document specifies common basic principles for gas infrastructure. Users of this standard are expected to be aware that more detailed national standards and/or code of practice can exist in the CEN member countries.
This document is intended to be applied in association with these national standards and/or codes of practice setting out the above-mentioned basic principles.
In the event of conflicts in terms of more restrictive requirements in national legislation/regulation with the requirements of this standard, the national legislation/regulation takes precedence as illustrated in CEN/TR 13737.
CEN/TR 13737 gives:
- clarification of all legislations/regulations applicable in a member state;
- if appropriate, more restrictive national requirements;
- a national contact point for the latest information.
EN 17649:2022/prA1 - Gas infrastructure - Safety Management System (SMS), Pipeline Integrity Management System (PIMS) and Compressor station integrity management system (CIMS) - Functional requirements
Odbor: HZN/TO 505 (Prijenos i distribucija plina)
Ustanova izvornika:
Rok za komentiranje: 2025-07-28
Podaci o nacrtu
Prikaži višePrikaži manje
 

This document specifies requirements on the development and implementation of a Safety Management System (SMS) and a Pipeline Integrity Management System (PIMS). The SMS is applicable for system operators of a gas infrastructure. The PIMS is applicable for system operators of gas infrastructure with a maximum operating pressure (MOP) over 16 bar.
This document refers to all activities and processes related to safety aspects and performed by system operators of a gas infrastructure, including those activities entrusted to contractors. It includes safety-related provisions on operation of the gas infrastructure.
This document is applicable to infrastructure for the conveyance of processed, non-toxic and non-corrosive natural gas according to EN ISO 13686 and gases such as biomethane and hydrogen and to mixtures of these gases with natural gas.
This document covers also gases classified as group H, that are to be transmitted, injected into and from storages, distributed and utilized, as specified in EN 16726. For the requirements and test methods for biomethane at the point of entry into a natural gas network, reference is made to EN 16723-1.
This document can be applied for gas infrastructure conveying gases of the 3rd gas family as classified in EN 437 or for other gases such as carbon dioxide.
Specific requirements for occupational health and safety are excluded from this document. For these, other European and/or international standards, e.g. ISO 45001, apply.
This document specifies common basic principles for gas infrastructure. It is important that users of this document are expected to be aware that more detailed national standards and/or codes of practice exist in the CEN member countries. This document is intended to be applied in association with these national standards and/or codes of practice setting out the above-mentioned basic principles.
In the event of conflicts in terms of more restrictive requirements in national legislation/regulation with the requirements of this document, the national legislation/regulation takes precedence as illustrated in CEN/TR 13737 (all parts).
NOTE CEN/TR 13737 (all parts) contains:
- clarification of relevant legislation/regulations applicable in a country;
- if appropriate, more restrictive national requirements;
- national contact points for the latest information.

prEN 12814-6 - Testing of welded joints of thermoplastics semi-finished products - Part 6: Low temperature tensile test
Odbor: HZN/TO 531 (Plastika i guma)
Ustanova izvornika:
Rok za komentiranje: 2025-07-28
Podaci o nacrtu
Prikaži višePrikaži manje
 

This document specifies the dimensions, the method of sampling and the preparation of the test specimens, also the conditions for performing the low temperature tensile test perpendicular to the weld in order to determine the low temperature tensile welding factor.
A low temperature tensile test can be used in conjunction with other tests (e.g. bend, tensile creep, macro) to assess the performance of welded assemblies, made from thermoplastics materials.
The low temperature tensile welding factor and the appearance of the fracture surface provide a guide regarding the ductility of the joint and the quality of the work.
The test is applicable to co-axial or co-planar welded assemblies made from thermoplastics materials filled or unfilled, but not reinforced, irrespective of the welding process used.
The test is not applicable for co-axial welded assemblies of an external diameter less than 20 mm.

prEN 13100-3 - Non destructive testing of welded joints in thermoplastics semifinished products - Part 3: Ultrasonic testing
Odbor: HZN/TO 531 (Plastika i guma)
Ustanova izvornika:
Rok za komentiranje: 2025-07-28
Podaci o nacrtu
Prikaži višePrikaži manje
 

This document specifies methods for the manual ultrasonic examination of heated tool, electrofusion, extrusion and hot gas joints in plastics materials. It applies to joints in single wall pipes and plates. The range of thicknesses covered is from 10 mm to 100 mm.
This document does not specify acceptance levels of the indications.

 

prEN ISO 22705-1 - Springs - Measurement and test parameters - Part 1: Cold formed cylindrical helical compression springs (ISO 22705-1:2021)
Odbor: HZN/TU M1 (Metalni materijali 1)
Ustanova izvornika:
Rok za komentiranje: 2025-07-28
Podaci o nacrtu
Prikaži višePrikaži manje
 

This document specifies the measurement and test methods for the general characteristics of cold formed helical compression springs made from round wire, excluding dynamic testing.

prEN ISO 22705-2 - Springs - Measurement and test parameters - Part 2: Cold formed cylindrical helical extension springs (ISO 22705-2:2023)
Odbor: HZN/TU M1 (Metalni materijali 1)
Ustanova izvornika:
Rok za komentiranje: 2025-07-28
Podaci o nacrtu
Prikaži višePrikaži manje
 

This document specifies the measurement and test methods for general characteristics of cold
formed helical extension springs made from round wire, excluding dynamic testing.

prEN ISO 22705-3 - Springs - Measurement and test parameters - Part 3: Cold formed cylindrical helical torsion springs (ISO 22705-3:2024)
Odbor: HZN/TU M1 (Metalni materijali 1)
Ustanova izvornika:
Rok za komentiranje: 2025-07-28
Podaci o nacrtu
Prikaži višePrikaži manje
 

This document specifies the measurement and test methods for general characteristics of cold
formed cylindrical helical torsion springs made from round wire, excluding dynamic testing.

prEN 18196 - Algae and algae products —Determination of inorganic arsenic in algae and algae products by anion-exchange (HPLC-ICP-MS)
Odbor: HZN/TU C1 (Kemikalije, kemijsko inženjerstvo, poljoprivredni i prehrambeni proizvodi 1)
Ustanova izvornika:
Rok za komentiranje: 2025-07-28
Podaci o nacrtu
Prikaži višePrikaži manje
 

This document describes a method for the determination of inorganic arsenic in algae by anion-exchange HPLC-ICP-MS following water bath extraction. Inorganic arsenic consists of arsenite, As(III) and arsenate, As(V).

A representative test portion of the sample is treated with a diluted nitric acid and hydrogen peroxide solution in a heated water bath. Hereby the arsenic species are extracted into solution and As(III) is oxidised to As(V). The inorganic arsenic is selectively separated from other arsenic compounds using anion exchange HPLC (High Performance Liquid Chromatography) coupled on-line to the element-specific detector ICP-MS (Inductively Coupled Plasma Mass Spectrometry) for the determination of the mass fraction of inorganic arsenic. External calibration with solvent matrix-matched standards is used for quantification of the amount of inorganic arsenic.

The method is based on method EN16802: Inorganic arsenic in food of plant and marine origin by HPLC-ICPMS, but covers more algae species. The present AsSugar species in certain algae can cause As peaks which might overlap with the As peaks related to the inorganic As. The current method includes a gradient elution method with quality criteria to ensure a correct identification of the inorganic arsenic.

prEN 18197 - Algae and algae products — Determination of the amino acid profile of micro- and macroalgae
Odbor: HZN/TU C1 (Kemikalije, kemijsko inženjerstvo, poljoprivredni i prehrambeni proizvodi 1)
Ustanova izvornika:
Rok za komentiranje: 2025-07-28
Podaci o nacrtu
Prikaži višePrikaži manje
 

This document describes a method for determining the amino acid profile of algal biomass. 
It specifies a method for the determination, in one single analysis, of the following amino acids: alanine, arginine, aspartic acid (combined with asparagine), cystine (dimer of cysteine, combined with cysteine), glutamic acid (combined with glutamine), glycine, histidine, isoleucine, leucine, lysine, methionine, phenylalanine, proline, serine, threonine, tyrosine and valine.
This method does not apply to the determination of tryptophan. The existing draft standard ISO/DIS 4214 – Milk and milk products – Determination of amino acids in infant formula and other dairy products will be evaluated and adapted.

prEN 18198 - Algae and algae products — Nitrogen content measurement and protein content calculation for micro- and microalgae
Odbor: HZN/TU C1 (Kemikalije, kemijsko inženjerstvo, poljoprivredni i prehrambeni proizvodi 1)
Ustanova izvornika:
Rok za komentiranje: 2025-07-28
Podaci o nacrtu
Prikaži višePrikaži manje
 

This document describes a method for determining the total protein content of algal biomass. 
Therefore, an existing method for measurement and calculation will be adapted.
The method consists of the measurement of the nitrogen content by a practical test method and the calculation of the protein content by a coefficient.
The document will describe the test method for nitrogen measurement. 
As the coefficient usually used for protein determination (6.25) is too high for algae, the document will give a recommendation for a coefficient which is more specific to algae and thereby more accurate.  

prEN ISO 23308-4 - Energy efficiency of industrial trucks - Test methods - Part 4: Variable-reach rough-terrain trucks (ISO/DIS 23308-4:2025)
Odbor: HZN/TU T1 (Prijevoz, rukovanje materijalima i pakiranje 1)
Ustanova izvornika:
Rok za komentiranje: 2025-08-01
Podaci o nacrtu
Prikaži višePrikaži manje
 

This document specifies the method of fuel consumption measurement for rough terrain- truck variable-reach trucks as defined in ISO 5053-1, herein after referred to as trucks. It does not apply to slewing trucks having a movement of more than 5° either side of the longitudinal axis.
This part is intended to be used in conjunction with ISO 23308-1. Where the requirements of this part differ from that in part 1, requirements in this part 4 will take precedence.

prEN ISO 3691-1 - Industrial trucks - Safety requirements and verification - Part 1: Self-propelled industrial trucks, other than driverless trucks, variable-reach trucks and burden-carrier trucks (ISO/DIS 3691-1:2025)
Odbor: HZN/TU T1 (Prijevoz, rukovanje materijalima i pakiranje 1)
Ustanova izvornika:
Rok za komentiranje: 2025-08-01
Podaci o nacrtu
Prikaži višePrikaži manje
 

ISO 3691-1:2011 gives safety requirements and the means for their verification for the following types of self-propelled industrial trucks, as defined in ISO 5053: industrial counterbalanced trucks; reach trucks with retractable mast or retractable fork arm carriage; straddle trucks; pallet-stacking trucks; high-lift platform trucks; trucks with elevating operator position up to 1 200 mm; side-loading trucks (one side only); lateral-stacking trucks (both sides), and lateral- and front-stacking trucks; pallet trucks; bidirectional and multidirectional trucks; tractors with a drawbar pull up to and including 20 000 N; rough-terrain, counterbalanced trucks; industrial trucks powered by battery, diesel, gasoline or LPG (liquefied petroleum gas).

prEN ISO 105-C09 - Textiles - Tests for colour fastness - Part C09: Colour fastness to domestic and commercial laundering - Oxidative bleach response using a non-phosphate reference detergent incorporating a low temperature bleach activator (ISO/DIS 105-C09:2025)
Odbor: HZN/TO 560 (Tekstilni proizvodi)
Ustanova izvornika:
Rok za komentiranje: 2025-08-01
Podaci o nacrtu
Prikaži višePrikaži manje
 

This part of ISO 105 specifies a method for determining the consumer relevant shade change of textiles, of all kinds,
(excluding silk and wool) and in all forms, to domestic/commercial laundering procedures in which a bleach activator
(oxygen bleaching system) is used.
The colour fastness resulting from oxygen bleaching in this test provides an indication of the shade change behaviour
observed after multiple domestic/commercial launderings.
This part of ISO 105 is not applicable for the assessment of the dye staining of adjacent fabrics, where suitable
methods are described in ISO 105-A04.
This part of ISO 105 does not reflect the contribution of optical brighteners, which are present in some commercial
washing products, to shade change.
This part of ISO 105 specifies a procedure incorporating the use of ECE1) non-phosphate reference detergent,
sodium perborate tetrahydrate, and the bleach activator tetra-acetylethylenediamine (TAED). An alternative test
procedure using the AATCC 1993 zero phosphate reference detergent (without optical brightener), and incorporating
sodium perborate monohydrate and the bleach activator sodium nonanoyloxybenzene sulphonate (SNOBS) is
currently under development.

prEN ISO 25086-1 - Textiles - Determination of the snagging resistance of fabrics - Part 1: Mace test method (ISO/DIS 25086-1:2025)
Odbor: HZN/TO 560 (Tekstilni proizvodi)
Ustanova izvornika:
Rok za komentiranje: 2025-08-01
Podaci o nacrtu
Prikaži višePrikaži manje
 

This document describes a test method for the determination of snagging resistance of a fabric using a mace.
This test method is applicable to knitted and to woven fabrics.

prEN ISO 10121-1 - Test method for assessing the performance of gas-phase air cleaning media and devices for general ventilation - Part 1: Gas-phase air cleaning media (ISO/DIS 10121‑1:2025)
Odbor: HZN/TO 541 (Sustavi grijanja, ventilacije i klimatizacije u građevinama)
Ustanova izvornika:
Rok za komentiranje: 2025-08-03
Podaci o nacrtu
Prikaži višePrikaži manje
 

ISO 10121-1:2014 aims to provide an objective laboratory test method, a suggested apparatus, normative test sections and normative tests for evaluation of three different solid gas-phase air cleaning media (GPACM) or GPACM configurations for use in gas-phase air cleaning devices intended for general filtration applications. ISO 10121-1:2014 is specifically intended for challenge testing and not for general material evaluation or pore system characterization. The three different types of GPACM identified in ISO 10121-1:2014 are GPACM-LF (particles of different shape and size intended for e.g. Loose Fill applications), GPACM-FL (FLat sheet fabric intended for e.g. flat one layer, pleated or bag type devices) and GPACM-TS (three dimensional structures that are many times thicker than flat sheet and e.g. used as finished elements in a device). The tests are conducted in an air stream and the GPACM configurations are challenged with test gases under steady-state conditions. Since elevated gas challenge concentrations (relative to general ventilation applications) are used, test data should be used to compare GPACM within the same configuration and not for the purpose of predicting performance in a real situation. It is also not implied that different GPACM configurations can be directly compared. The primary intention is to be able to compare like GPACM configurations to like, not between GPACM configurations. Testing of complete devices is described in ISO 10121‑2.
To ensure objectivity for test equipment suppliers, no specific design of the test apparatus is defined: an example is illustrated in an annex. Instead normative demands for media sample holder design, apparatus properties and validation tests are specified.

prEN 3293 - Aerospace series - Bolts, T-head, close tolerance, medium thread length, in heat resisting nickel base alloy NI-P100HT (Inconel 718), uncoated - Classification: 1 275 MPa/650 °C
Odbor: HZN/TU T1 (Prijevoz, rukovanje materijalima i pakiranje 1)
Ustanova izvornika:
Rok za komentiranje: 2025-08-04
Podaci o nacrtu
Prikaži višePrikaži manje
 

This document specifies the dimensions of uncoated T-head bolts, close tolerance, with MJ-thread, medium thread length, in heat-resisting nickel base alloy NI-P100HT for aerospace applications.
Maximum test temperature of the parts is 650 °C.
These bolts are used in aerospace fastening systems mainly stressed in shearing force.

prEN 3327 - Aerospace series - Bolts, double hexagon head, close tolerance, medium thread length, in heat resisting nickel base alloy NI-P100HT (Inconel 718), uncoated - Classification: 1 275 MPa/650 °C
Odbor: HZN/TU T1 (Prijevoz, rukovanje materijalima i pakiranje 1)
Ustanova izvornika:
Rok za komentiranje: 2025-08-04
Podaci o nacrtu
Prikaži višePrikaži manje
 

This document specifies the dimensions of uncoated double hexagon head bolts, close tolerance, with MJ-thread, medium thread length, in heat-resisting nickel base alloy NI-P100HT for aerospace applications.
Maximum test temperature of the parts is 650 °C.
These bolts are used in aerospace fastening systems mainly stressed in shearing force.